Loading design…
sundevilmotorsports
PCB development repository
| Reference | Value | Description |
|---|---|---|
| IC1 | ESP32-S3-WROOM-1-N8R8 | WiFi Modules - 802.11 (Engineering Samples Only) SMD Module, ESP32-S3R8 with 8 MB Octal PSRAM Die, 8 MB Quad SPI flash, PCB Antenna |
| IC2 | TPS259250DRCR | 5V, 5A, 30m eFuse with Adjustable +/-15% Accurate Current Limit |
| IC3 | CP2102N-A02-GQFN28 | SILICON LABS - CP2102N-A02-GQFN28 - USB TO UART BRIDGE, -40 TO 85DEG C |
| IC4 | TLP175A_TPL,E | MOSFET Output Optocouplers Trigger LED Current 1mA85dC3750 Vrms |
| IC5 | MIC37100-3.3WS | LDO Voltage Regulators 1.0A Low Voltage uCap LDO Regulator |
| IC6 | TPS2116DRLR | d |
| IC7 |
| Character/Graphic TFT LCD Controller |
| IC8,IC9 | SN74AHC1G125DBVR | Single Bus Buffer Gate with 3-State Output |
|---|
| Q1,Q2 | MMBT2222LT1G | Bipolar transistor symbol for simulation only, substrate tied to the emitter |
|---|
| U1 | USBLC6-2SC6 | Very low capacitance ESD protection diode, 2 data-line, SOT-23-6 |
|---|
| U2 | SN65HVD230 | CAN Bus Transceivers, 3.3V, 1Mbps, Low-Power capabilities, SOIC-8 |
|---|
| U10 | EMIF06-MSD02N16 | 6-Line EMI filter&ESD for SD card uQFN16 STMicroelectronics EMIF06-MSD02N16, EMI Filter & ESD Protector |
|---|
| C1,C14,C15 | 10uF |
|---|
| C2,C4,C8,C10,C11,C13,C17,C18,C22,C23,C25-C28,C31-C36 | 100nF |
|---|
| C3,C5,C6,C9,C12,C16,C19-C21,C24 | 1uF |
|---|
| C7 | 4.7uF |
|---|
| C29,C30 | 15pF |
|---|
| D1 | ESDCAN03-2BWY | ESD Suppressors / TVS Diodes Automotive dual-line Transil, Transient voltage suppressor (TVS) for CAN bus |
|---|
| D2-D4 | MBR0540T1G | Guardring for Stress Protection; Very Low Forward Voltage; Epoxy Meets UL94, VO at 1/8"; Package Designed for Optimal Automated Board Assembly Mechanical Characteristics:; Reel Options: 3,000 per 7 inch reel / 8 mm tape; Reel Options: 10,000 per 13 inch reel / 8 mm tape; Device Marking: B4; Polarity Designator: Cathode Band; Weight: 11.7 mg (approximately); Case: Epoxy Molded; Finish: All External Surfaces Corrosion Resistant and Terminal Leads are Readily Solderable; Lead and Mounting Surface Temperature f |
|---|
| H1-H6 | M3 |
|---|
| J1,J2 | Conn_01x02 | Generic connector, single row, 01x02, script generated (kicad-library-utils/schlib/autogen/connector/) |
|---|
| J3 | ESP_USB | USB Micro Type B connector |
|---|
| J4 | Conn_01x04_Socket | Generic connector, single row, 01x04, script generated |
|---|
| J5 | Conn_01x40_Pin | Generic connector, single row, 01x40, script generated |
|---|
| J6 | Conn_01x02_Pin | Generic connector, single row, 01x02, script generated |
|---|
| J7 | Molex_1040310811 | Micro SD Card Socket with two card detection pins |
|---|
| L1 | 4.7uH |
|---|
| LED1 | 150060GS75000 | Wurth Elektronik WL-SMCW 520 nm Green LED, 1608 (0603) Clear SMD package |
|---|
| LED2 | 150060RS75000 | WURTH ELEKTRONIK - 150060RS75000 - LED, 0603, RED, 250MCD, 625NM |
|---|
| LED3-LED8 | Amazon LED |
|---|
| PS1 | TPS61169DCKR | TPS61169 38-V High-Current Boost WLED Driver |
|---|
| R1,R3,R5,R8,R9,R14,R15,R19,R20,R24,R26,R31,R59 | 10k | Resistor |
|---|
| R2,R34 | 5.05 |
|---|
| R4 | 60.4k |
|---|
| R6,R10,R29,R30,R32,R33,R35-R41,R48,R50-R53,R57,R58 | 33 |
|---|
| R7,R55 | 1M |
|---|
| R12,R13 | 27 |
|---|
| R16 | 22.1K |
|---|
| R17 | 1k |
|---|
| R18 | 47.5K |
|---|
| R21 | 120 |
|---|
| R22,R27,R28,R42-R47,R49,R54 | 220 | Resistor |
|---|
| R23 | 0 |
|---|
| R25 | 68 |
|---|
| S1,S2 | MHPS2285V | Pushbutton Switches DPDT 0.1A 30V On-Mom |
|---|
| VR1-VR3 | PCW1J-B24-KEB103L | 10k Ohm 1 Gang Linear Panel Mount Potentiometer None 1.0 Kierros Conductive Plastic 0.75W, 3/4W PC Pins |
|---|
| VR4,VR5 | P091N-2QC20BR10K | Panel Pot, side adjust, 1 gang, 10 kOhms, 50 VAC, Knurled / Slotted 20 mm |
|---|
| Y1 | ABM3B-20.000MHZ-10-1-U-T | 20 MHz +/-10ppm Crystal 10pF 50 Ohms 4-SMD, No Lead |
|---|